Best Software Settings for Fiber Laser Marking Machine

Best Software Settings for Fiber Laser Marking Machine (Beginner to Pro Guide)

Introduction

Using a fiber laser marking machine is not only about having good hardware. The software settings play a very important role in marking quality, engraving depth, speed, and final results.

Many beginners face problems like:

Light or faded marking
Burn marks
Uneven engraving
Poor contrast on metal

All these issues happen because of incorrect software settings. In this article, I will explain the best software settings for fiber laser marking machine in very simple language, so you can understand and apply them easily.

Why Software Settings Are Important in Fiber Laser Marking

The software controls how the laser behaves on the material. Correct settings help you:

Get clean and sharp marking
Achieve proper engraving depth
Avoid material damage
Save time and energy

Even a powerful machine will give poor results if the settings are wrong.

Most Common Software Used for Fiber Laser Marking

Before setting parameters, you must know which software you are using.

Popular Fiber Laser Software

EZCAD (Most common and beginner friendly)
LightBurn (Controller dependent)
CorelDRAW (Design preparation)
AutoCAD (Technical drawings)

Most fiber laser machines work mainly with EZCAD, so the settings below are based on EZCAD logic.

Basic Software Parameters You Must Understand

Let’s understand each setting in a simple way.

1. Power (%) – Laser Strength

Power controls how strong the laser beam is.

Recommended Power Settings

Light marking: 20% – 40%
Normal marking: 50% – 70%
Deep engraving: 80% – 100%

👉 Start with low power and increase slowly.

2. Speed (mm/s) – Marking Movement Speed

Speed controls how fast the laser moves.

Recommended Speed Settings

Fine marking: 800 – 1500 mm/s
Normal engraving: 500 – 800 mm/s
Deep engraving: 100 – 400 mm/s

👉 Lower speed = deeper engraving
👉 Higher speed = lighter marking

3. Frequency (kHz) – Pulse Control

Frequency controls how many laser pulses hit the material.

Recommended Frequency Settings

Stainless steel marking: 20 – 30 kHz
Aluminum marking: 30 – 60 kHz
Deep engraving: 20 – 25 kHz

👉 Lower frequency gives deeper engraving
👉 Higher frequency gives smooth surface finish

4. Hatch Settings – Filling the Design

Hatch settings control how the laser fills your design.

Best Hatch Settings

Hatch type: Line
Hatch angle: 0° / 90°
Hatch spacing: 0.02 – 0.05 mm

👉 Smaller spacing = darker marking
👉 Use cross-hatch for deep engraving

5. Pass Count – Number of Laser Passes

Instead of using very high power, you can increase passes.

Recommended Passes

Light marking: 1 pass
Medium engraving: 2–3 passes
Deep engraving: 5+ passes

👉 Multiple passes give better control and clean results.

Best Settings Example (Starter Preset)

For Stainless Steel (20W–30W Machine)

Power: 60%
Speed: 700 mm/s
Frequency: 25 kHz
Hatch spacing: 0.03 mm
Passes: 2

(Always test on scrap material first)

File Formats Supported by Fiber Laser Software

Your software will work best with vector files.

Recommended File Formats

DXF – Best for laser work
CDR – CorelDRAW format
SVG – Scalable vector
AI – Adobe Illustrator
PLT – Plotter format

Get Ready-to-Use Laser Design Files (Very Important)

If you don’t want to waste time creating designs, you can directly download ready-to-use laser files.

👉 Go to GlobalStreek.com

There you will get:

✅ Free laser cutting & marking designs
✅ Premium and fresh design files
✅ DXF & CDR formats
✅ Designs ready to engrave, mark, or cut

These files are perfect for fiber laser marking machines and save a lot of setup time.

Common Mistakes Beginners Should Avoid

❌ Using 100% power all the time
❌ High speed with low power
❌ Not focusing the laser properly
❌ Skipping test runs
❌ Using low-quality design files

Avoiding these mistakes will instantly improve your results.

Which Settings Are Best?

There is no single perfect setting for all materials.

Best practice is:

Start with low power
Adjust speed slowly
Test frequency
Use multiple passes
Always test on scrap material

This method gives consistent and professional results.

Conclusion

The best software settings for fiber laser marking machine depend on material, machine wattage, and design quality. When you understand power, speed, frequency, hatch, and passes, you gain full control over your marking results.

Combine correct settings with high-quality laser design files from GlobalStreek.com, and you will get clean, sharp, and professional engraving every time.

Best Software Settings for Fiber Laser Marking Machine